-
product
Astronics PXIe-6943, 1-Slot, 50 MHz, 32-Channel PXI Digital Pattern Instrument
785855-01
1-Slot, 50 MHz, 32-Channel PXI Digital Pattern Instrument - The Astronics PXIe-6943 works as a core component of digital test systems that may include switching, analog instrumentation, and an RF subsystem. This instrument features an advanced thermal design, temperate monitoring, … and a high-speed data sequencer for control of stimulus and response patterns. Additionally, the Astronics PXIe-6943 operates at data rates up to 50 MHz with 1 ns edge placement, variable slew rates, and a <3 ns channel-to-channel skew. It also supports synchronized digital test systems from 32 to 224 channels.
-
product
Battery Module (60v-300v) Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
The module test equipment adopts sinexcel advanced high frequency isolation scheme, and the detection process supports multi-gear switching. The equipment integrates voltage, temperature, pressure and other auxiliary channels, and can also integrate temperature box, water cooler and other equipment, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
product
EBIRST 23 X SMB Verification Fixture
93-011-101
The 93-011-101 23 x SMB Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
AC Insulation Testing
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 3-Channel, 4-Pole
40-514-101
The 40-514-101 (PXI) and 42-514-101 (PXIe) are low density multiplexers in dual 3-channel, 4-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
PXI-2798, 40 GHz, Dual-Transfer PXI Transfer Switch Module
782358-01
40 GHz, Dual-Transfer PXI Transfer Switch Module—The PXI‑2798 can route RF or microwave signals in automated test applications. Designed to operate with less than 1 dB insertion loss at up to 40 GHz, the PXI‑2798 appears almost invisible to signals at much lower frequencies as well. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2798 is also well-suited for passing high-order harmonics from RF upconverters or routing multiple sources to RF downconverters.
-
product
Twin columns automated force test stand 48" travel - 20,000 lb
720TN
The advanced 720TN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
LED Driver Aging Rack
LEDRACK-100W192P
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal outp...show more -
product
Analogue (1kV below) Insulation Tester
2732 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar an...show more -
product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety sta...show more -
product
Test Sockets
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available
-
product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
product
300W Electronic Load
EL3630B
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
product
Single Board Source/Meter/Switch
SMSU
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
product
PXI-2569 , 31-Channel, 2 A, SPST PXI Relay Module
778572-69
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2569 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It is fully software programmable and contains a 32,000‑step scan list for deterministic scanning capability. This module offers maximum relay density, so it is ideal for medium-power automated test loads.
-
product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
product
EBIRST 104-pin D-type Test Tool
93-022-001
The 93-022-001 eBIRST 104-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
500 Amps, 2 MHz BW Current Probe - AC/DC , 700 Amp Peak
CP500
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
12-1000V AC Adjustable Non-Contact Voltage Tester
5220A
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from12V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
Analoge Sound Level Meter
Model KM-20/ YF-20
Kusam Electrical Industries Limited
• One-handed simple, easy to operate.• Inbuilt reference signal.• Inbuilt battery test.• Quickly, accurately measures sound level.• Compressed scales minimise range switching.• An internal reference signal is available for checking the meter’s operation.• Calibration Check• Microphone with Capacitance Microphone.
-
product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
Test Enclosures
The HV test hood, developed by us in accordance with EN50191 standard (erection and operation of fixed and temporary electrical test installations), is designed for testing large quantities in ongoing production. The ergonomic design ensures fatigue-free operation even during repetitive work sequences. Equipped with all safety-relevant functions, such as safety switch and locking of the hood cover during the test sequence, the operator is optimally protected at all times.The interchangeable adapter plate within the test cell allows quick adaptation for different test conditions and test situations.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InPD1012-60
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Test board with K-connectors can be providedDC-60GHz40+ Gbps
-
product
XCITE 1100 Field Test Series
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
product
6-Slot LXI/USB Modular Chassis With Scan List Sequencing & Triggering
60-106-002
Pickering Interfaces’ 60-106-002 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. It features remote control via USB or LXI Ethernet and this version of the chassis includes Scan List Sequencing & Triggering. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
product
LXI Switch and Control Instruments
L4400 Series
The Keysight L4400 Series of switches, digital input/output and analog output instruments offer the best tradeoff in size, functionality and test. They are standalone instruments that perform the same function as their companion 34980A-Series plug-in modules. They come with a fully operational programming interface including a web-page for easy control.
-
product
1435 Series Signal Generator (9kHz to 40GHz)
1435
1435 series signal generator achieves balance in terms of performance, economy and volumetric weight. It responds fast and switches to another frequency in only 1ms, which shortens the test time and improves test efficiency, meeting the needs of massive data testing.
-
product
PCI Multiplexer Cards
*High-density 4-bank, 24-channel, 2-pole multiplexers*2 Amp multiplexer range with 18 configurations between single 64-channel 1-pole and quad 8-channel 2-pole*High-density multiplexers with switching formats between 5-channel, 32-pole and 198-channel, 1-pole*High-voltage multiplexers designed for cable testing applications*Supported our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures our switch systems.